Qingdao G&Z Trading Co.,Ltd

Contact US

Address: Room 2901, Bldg 1, Zijin Plaza, Qingdao E&T Development Zone, Shandong 266555, China

TEL: +86-532-80980931

FAX : +86-532-80980932

Mobile: 0086 13963970719 (whatsapp number)

Email: ziwei@gzcngroup.com

Website: http://www.gzcnmachinery.com/

               www.gzcngroup.com 

Home > News > Content
Four Causes The Accuracy Of The Manual Die Cutting Machine To Drop
- Sep 22, 2017 -

Four causes the accuracy of the Manual Die Cutting Machine to drop
First, on the Manual Die Cutting Machine or the next Manual Die Cutting Machine version positioning are not allowed.
The machine for a long time will cause Manual Die Cutting Machine or Manual Die Cutting Machine on the bottom plate of the positioning block wear, so that the gap is too large and lead to Manual Die Cutting Machine to reduce the accuracy. The positioning block should be replaced at this time. Side positioning plate wear is an important factor in the side positioning is not allowed. As the positioning of the dialing is not enough to make up for good wear, it will cause poor positioning side positioning accuracy. Replace the side positioning plate at this time.
Second, before and after the positioning of the pendulum positioning distance is too small.
Because the length of the chain itself has a certain error, if the positioning distance is too small, the front and rear positioning can not eliminate the chain error, thus affecting the precision of the Manual Die Cutting Machine. At this point should be adjusted before the positioning of the pendulum screw or post-positioning pendulum cam position, so that the front and rear positioning frame to stop the teeth 2mm ~ 3mm distance is appropriate.
Third, gripper pressure is too small or uneven.
If the gusset's active dental elasticity becomes smaller due to long-term use, it will cause the paper to slip or fall off during the transfer process, which directly affects the accuracy of the Manual Die Cutting Machine. The uneven pressure between the grippers may cause the paper to Manual die - cutting machine in the process of skew. At this time should change the active teeth. In addition, the fixed teeth in the horizontal height should also be consistent, otherwise it may be in the gripper paper collision or gripper paper wrinkles, affecting the accuracy of Manual Die Cutting Machine.
Fourth, the process of conveying the cardboard, the main drive chain wear and tear elongation, will directly affect the positioning of the manual die before the positioning accuracy.
At this point to replace the chain. Intermittent mechanism wear, resulting in tooth row in the stop or start the process of jitter, will also affect the accuracy of Manual Die Cutting Machine. In this case generally only affect the positioning accuracy, this time, should be timely maintenance.
 Manual Die Cutting Machine is through the upper and lower stamping way to advance in accordance with the product drawings to open a good product model stamping into a certain shape, the entire Manual Die Cutting Machine operation process is driven by the servo motor driven automatic feeding machine, through Feeding can complete some of the action of the film, through the Manual Die Cutting Machine die-type punch, drained the border of the waste, cut out into pieces can complete all the process.
Manual Die Cutting Machine die-cutting accuracy is not high problem is very common. One of the most important criteria for measuring die-cutting quality is the precision of die-cutting, which is an important guarantee for qualified products. The reason for the failure is very high. The reason why the precision of the Manual Die Cutting Machine is not high:
First, before and after the positioning of the pendulum positioning distance is relatively small. Due to the length of the chain itself, a certain error, such as positioning distance is too small, then the front and rear positioning can not eliminate some of the chain error, affecting die cutting accuracy. Adjust the position of the pendulum before the adjustment screw or post-positioning pendulum cam position, so that the front and rear positioning frame to stop the teeth 2mm ~ 3mm distance is appropriate.
Second, on the die-cutting or die-cutting version of the positioning are not allowed. Manual Die Cutting Machine The machine for a long time will cause die-cutting frame or die-cutting plate on the positioning block wear. Side positioning plate wear is an important factor in the side positioning is not allowed. As the positioning of the dialing is not enough to make up for good wear, it will cause poor positioning side positioning accuracy. Replace the side positioning plate at this time.
Third, the cardboard transfer process, the main drive chain wear and tear elongation, will directly affect the positioning accuracy before die cutting. At this point to replace the chain. Intermittent mechanism wear, resulting in tooth row in the stop or start the process of jitter, will also affect the die cutting accuracy. In this case generally only affect the positioning accuracy, this time, Manual Die Cutting Machine should be timely maintenance.
Fourth, gripper pressure is too small or uneven. If the gripper's active dental elasticity becomes smaller due to long-term use, it will cause the paper to slip or fall off during the transfer process, which directly affects the die-cutting accuracy. Uneven pressure between the grippers may cause the paper to The process of skew. At this time should change the active teeth. In addition, the fixed teeth in the horizontal height should also be consistent, otherwise it may be in the gripper paper collision or gripper paper wrinkles, affecting the cutting accuracy.